If you know what you need... click here:


Ordering The EZ-Level Cabinet Levelers

You only need to know Two Things ...

1: How Many Levelers Do I Need?

2: What Size Do I Need?





1: How Many Levelers Do I Need?
cabinet levelers

EZ-Levels are sold primarily in "SETS" (see photo)
Each "SET" consists of:

(1) "front" and (1) "rear" leveler
A "short" adjusting rod for the front leveler
A "long" adjusting" rod to reach the rear leveler
Mounting Screws

Note: The "Short" adjusting rod screws into the front leveler. The "long" adjusting rod simply passes through the front leverler enabling installers to adjust the BOTH levelers independant of one another ... without crawling under the cabinets.

Product Spec Sheet















Therefore ... "independent" cabinets will need (2) sets (see photo below left)































Cabinet Runs...

Most kitchens have several cabinet runs (cabinets that are screwed together side by side) which will only require (1) set on each end...
and (1) set at each "seam".

Therefore: If you have 2 cabinets side by side you will need (3) sets... (see photo to right).


Five cabinets side by side would need (6) sets and so on.














2: What Size Do I Need?

EZ-Levels are sold in 4 different sizes to accommodate the depths of any cabinet.

  • EZ-24:           (One set of levelers sized for a 24" deep cabinet)
  • EZ-21:           (One set of levelers sized for a 21" deep cabinet)
  • EZ-18:           (One set of levelers sized for a 18" deep cabinet)
  • EZ-Single     (A "Single" leveler sized for any cabinet 15" or less in depth)

***Note: Do not measure the toe-kick recess. We have done the math for you!***


For example: A set of EZ-24's actually measure 18" in overall length to accomodate the toe-kick recess.
You only need to know "what size cabinets your are installing".
No matter what size cabinets you have... simply order that size.





That's It !   That was easy!!!





Now... Grab your floor-plan "cabinet layout" and
lets add up your levelers

To do this... Simply print our your floor plan and draw arrows where the levelers will go.

(Note: In the example photo... we also drew in the levelers just to give you a better idea of what's going on)





"Independent" base cabinets: Must have (2) sets of levelers.













Sink Bases:
Sink bases are ALWAYS to be considered as an "independent" cabinet! WHY??? Because you will want to adjust this cabinet up and over your plumbing... independent of the other cabinets... then screw them together.
















Cabinet Runs:
Cabinet runs are cabinets that can be screwed together (both front and rear) like these two examples.

RULE: Cabinet runs will always have (1) set on each "side"... and (1) set at each "Seam". The "seam" is where the cabinets are screwed together.

It does not matter which side of the seam you install levelers. The seam is just as strong on one side as the other.

Footnote: You will screw all your "cabinet runs" together... and level them up as one big piece of furniture.

Notice the arrows are grouped together indicating these cabinets are a "cabinet run".












Fillers & Turnings:
3" Fillers or Turnings are usually not very strong at the joint (AND) they are not typically screwed together in the rear.

Therefore they do not qualify as a cabinet run and should be installed "independent" from one another... having levelers on both sides of the seam.

As a rule of thumb I always install and level all my cabinets first... THEN... cut and install my fillers.










This right side cabinet requires (2) sets because it is independent of the others.

You can also see how grouping your arrows helps to identify all the cabinet runs.















When joining cabinets that have different depths... always place the levelers on the LARGER side of the seam.



In this example cabinet #2 will have (2) sets of EZ-24's on it... while cabinets #1 and #3 will have EZ-21's on them (assuming they are 21" deep vanity cabinets)













Far Left: Triangular Bases require (1) "Single" unit at the end... and (1) standard set "shared" at the seam as you normally would with any run.



Far Right: Trapezoids require the same: (1) "Single" on end and (1) standard at seam.

















Notice: The bottom cabinet run also consists of an EZ-Single. (bottom right)





EXAMPLE PRICING -
This plan would require (10) EZ-24's and (1) EZ-Single.
$160


























Lazy Susans: Lazy Susans require (2) Sets of 24's. Note. You can still share a set at the seams... just make sure to mount BOTH Sets ON THE Lazy Susan itself. (see arrows)

(most of the time it does not matter which side of a seam you mount the levelers. In this case it does. This give you more control while leveling the large corner cabinet).






Blind Bases: Blind Bases require (2) Sets of 24's. Also... You must level up blind bases first. Then... set the adjacent appliance or cabinet into place... Then level those item(s) up. Otherwise you would not be able to reach the far set of levelers for adjustments.)

EXAMPLE PRICING -
This plan would run $120


















End Panels: (tall or short)

MOST use a standard set of EZ-Levels (left).

SOME have no toe kick recess (right)

Panels without toe kick recesses require the use of (2) "Single" levelers face them both inward as shown... Level the panel up... THEN install your appliance.Otherwise you would not be able to reach the far set of levelers for adjustments.

























... We are happy to help! ...

If you would like our staff to look over your plans we will be happy to do so at no charge. However, it's a good practice to go ahead and mark the locations on your floor plan as described above. We will make any changes if need be. If your plans are hand drawn that is fine too.

Our fax number is toll free: 866-284-3321
Or you can email us at Brooks@EZ-Level.com

For specialty layouts like islands etc... just send us your plans and we will layout the levelers for you again at no charge.

Please include your name, phone and email address (or fax) for response. We will usually respond back the same day.
If you are faxing please mark your info in BIG BOLD LETTERS because faxes are hard to read sometimes.

Top of Page

TEST