Note: If you have never purchased EZ-Levels before... Please click the link below: "Ordering Instructions" before you order. (for sizing and quantity)

Each Set Includes: (shown in photo)

• (2) Levelers (front & rear)
• (1) Front - Short Adjusting Rod 
• (1) Rear -  Long Adjusting Rod 
• Mounting Screws and (1) Drilling Jig included with every order.

Note: If you have never purchased EZ-Levels before... Please click the link below: "Ordering Instructions" before you order. (for sizing and quantity)

Each Set Includes: (shown in photo)

• (2) Levelers (front & rear)
• (1) Front - Short Adjusting Rod 
• (1) Rear -  Long Adjusting Rod 
• Mounting Screws and (1) Drilling Jig included with every order.

Note: If you have never purchased EZ-Levels before... Please click the link below: "Ordering Instructions" before you order. (for sizing and quantity)

Each Set Includes: (shown in photo)

• (1) Levelers (front & rear)
• (1) Front - Short Adjusting Rod 
• Mounting Screws and (1) Drilling Jig included with every order.

Single leveler only... To be used on 12" - 15" cabinets.

When purchasing levelers for any corner cabinet, make sure to add an EZ-Susan in the rear. This gives you the ability to lift the far back corner with ease... and keep it from sagging. 

The photo is showing (1) EZ-Susan mounted to the bottom of a corner cabinet. The cabinet is upside down, so you can see the leveler. 

With the EZ-Susan, we now level the Rear Corner first... then the other rear levelers. Then... simply adjust the front feet till they touch. NOW... leveling Susans usually takes less than a minute! 

Do I need this? No... But it's VERY VERY VERY helpful. 

Keep in mind, We ship a 3" long #2 bit with every EZ-level order, which works beautifully in any driver. However, I love this handheld driver, for all my Micro-Adjustments.  

I use a low voltage drill to raise cabinets (close) to the laser... and then use THIS tool to hit the line perfectly. Doing it this way means you will almost never overshoot the laser line.

If you're a homeowner, on a tight budget, you might not need this, but if you are a pro installer, then you definitely will want one!

Do I need this? No... BUT... it's VERY VERY VERY helpful!!!

When it comes to adjusting the EZ-Levels... any inexpensive low-voltage handheld driver is by far the best tool for the job!

Regular Drills... work, but they have way too much torque, so you have to be careful! 

This electric driver allows you to raise cabinets up quickly without the extra torque. It also features a great little light, which lights up the toe-kick area nicely.

I use one on just about every job. 

Now... you can BUY or RENT our top-of-the-line Green Line Self-Leveling Laser! Simply choose the "Buy or Rent option"

• Buy  = $79 
• Rent = $79  (If returned, $40 will be credited to your card).

You will have 60 days to return for credit)

The Huepar 9011G: Mounts onto any standard tripod, and features a super bright green Horizontal and Vertical line visible up to 100Ft! Sharper than red lasers and easier to see. 

Another great feature is the ability to LOCK the laser so that you can use it at angles for tiling etc. 

This is the ONLY JIG that allows installers to CUT THEIR CROWN RIGHT-SIDE-UP! 

Being able to cut crown molding "right-side-up" means cutting crown molding is as easy as cutting baseboard! No more cheat sheets... This is an absolute game-changer for installing crown molding! It's quick, easy, and inexpensive! (My kind of tool)! 

Cuts crown molding from 1"- 6" and fits in any miter saw. 

2P-10 Bonds crown molding miter joints in about 8 seconds! Pro tip: You never want to "nail" your mitered corners together. Instead, you want to glue those corners. Otherwise, expansion and contraction will cause those corners to separate over time. (Not to mention, trying to brad nail a mitered corner is no fun) This glue will set stronger than the wood itself. Simply glue... hold for 5-10 seconds and you're done! 

My crew and I have been using 2P-10 for years and would never consider installing crown without it. 

A MUST HAVE for any miter saw! The laser is very very accurate and makes cutting with precision a snap!

Fits most 7-1/4, 8, 8-1/4, 10, and 12-Inch Miter, sliding compound miter, chop, and portable saws New recessed laser design to protect the laser from hitting the material on deep cuts.

New thinner design to fit more saws. New brighter and more accurate laser line. Includes an extra set of silver oxide batteries. (lasts for years)!

Note: Does not fit 5/8" Radial Arm Saws

We've used every countersink bit available... but this bit is the best! Most importantly it does not burn up while drilling through cabinet styles as the others do. Also, It doesn't slip (like most do)... and the tapered design works wonders!

(This is the bit you will use to screw your cabinet styles together. AND... for hanging your cabinets on the wall. It works perfectly with the Decking screws)

We have been using these screws for years now. I wouldn't even consider using anything else.

1). They're a nice natural maple wood color. 
2). The bit doesn't slip. 
3). The tapered heads tuck in nicely and look sharp.
4). The wax coating causes them to glide in easily.

Use these with the Countersink Bit 

It's finally here!
The New 2023 StudFinder-Pro!

Simply Put...
This is the BEST stud finder we have ever used!

The SF-Pro features (4) Super Strong Rare Earth Magnets equidistantly spaced, to yield an incredible 8" Sweep Zone, finding studs in seconds with no false readings!

It finds studs so fast, that you can literally walk as you mark your studs!

No batteries!

This is the one Stud Finder that will work perfectly... 20 years from now!
(No Batteries! A must for any shop)!

NOT FOR LEVELING!.... (LOL)

Every kitchen will require the use of shims:   Behind the cabinets... In-between cabinets... etc.

We like these shims because they tend to break much more evenly than the traditional wooden shims. Composite Shims are difficult to find... so we've included them here for you.

(1) Pack should be plenty for the typical kitchen.

Simply put... These make your installation a LOT easier! As you can see we used a pair just like these throughout our entire video. They provide two functions. 1. Clamp the face frames together 2. Help to align those same frames, so they are smooth. (it's important because most frames are not perfect. Hence, the need for clamps. 

Each order of clamps comes with (2) clamps. (1 pair)

These little time savers are like having 4 extra hands to hold crown molding in place. Enabling one person to install crown molding throughout the house with no extra help. 

Note: These are not for "cabinet" crown molding.

Every kitchen has electrical outlets inside the cabinets (under the sink and above the microwave). What makes this difficult is the void between the cabinet and the wall.

In almost every case, there is a 3/4" void due to the fact that "most" cabinets are not flat on the backside. Moving the outlet out 3/4" is VERY difficult.

Therefore, we found this AWESOME inexpensive solution, making quick work of a very tough problem. (Click the dropdown and choose your color and style)